birt ean 13

birt ean 13

birt ean 13

birt ean 13

birt ean 13

birt ean 13,

birt ean 13,
birt ean 13,
birt ean 13,

birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,

birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,

birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,
birt ean 13,

Because many features in routed mode are unsupported in transparent mode, the configuration on the appliance is cleared To revert back to routed mode, use the no firewall transparent command SECURITY ALERT! When switching from routed to transparent mode, you are not prompted to continue the process the appliance immediately executes the command, your configuration is erased, and you re in transparent mode So if you want to try transparent mode on an appliance with a routed mode configuration, first back up the configuration before trying it! (You would think, given that the appliance is doing something this drastic, the appliance would first display a note to you about the ramifications of executing the command and then would give you the option to abort it) Once you ve converted the mode to transparent (or routed, for that matter), you can verify the mode with the show firewall command, like this:

The McGraw Hill Companies, 2001

You can assign an IP address to the appliance for management purposes This IP address has to be from the subnet the two interfaces are connected to For example, if you reexamine the right side of Figure 21-1, the management address would have to be an unused address from 10010 When you re assigning a management IP address to the appliance, the address must be from the subnet connected to the two interfaces on the appliance Here s the command to configure the management address:

2

ciscoasa(config)# ip address IP_address [subnet_mask] [standby IP_address]

access-date customer-name customer-id customer customer-street customer-city depositor account account-number balance

one pointing to the loan entity set and one pointing to the customer entity set (Figure 29c) If a relationship set has also some attributes associated with it, then we link these attributes to that relationship set For example, in Figure 210, we have the accessdate descriptive attribute attached to the relationship set depositor to specify the most recent date on which a customer accessed that account Figure 211 shows how composite attributes can be represented in the E-R notation Here, a composite attribute name, with component attributes rst-name, middle-initial, and last-name replaces the simple attribute customer-name of customer Also, a composite attribute address, whose component attributes are street, city, state, and zip-code replaces the attributes customer-street and customer-city of customer The attribute street is itself a composite attribute whose component attributes are street-number, street-name, and apartment number Figure 211 also illustrates a multivalued attribute phone-number, depicted by a double ellipse, and a derived attribute age, depicted by a dashed ellipse

21:

street-name middle-initial first-name name customer-id customer last-name street address city state zip-code street-number apartment-number

Notice that the ip address command is a global command you are not in an interface when configuring it The standby parameter assigns a management IP address to the standby unit in a failover configuration (failover is discussed in 23) Use the show ip address command to verify your management IP address configuration NOTE The assignment of a management address is optional Also the management address is just that: a management address For devices in the subnet, do not point them to this address as a default gateway Remember that the appliance is in transparent mode, acting as a layer 2 device: it is not acting as a router

A sales compensation plan with a hurdle provides differentiated payouts for a first measure depending on how well the seller performs on a second measure (see Figure 5-25)

The McGraw Hill Companies, 2001

As I mentioned in the Bridges vs Transparent Mode section, the appliances will build a MAC address table of source MAC addresses associated with an interface You can view the MAC address table with the show mac-address-table command:

Let us consider how we process this query using an ordered index First, we perform a lookup on value c1 Once we have found the bucket for value c1 , we follow the pointer chain in the index to read the next bucket in order, and we continue in this manner until we reach c2 If, instead of an ordered index, we have a hash structure, we can perform a lookup on c1 and can locate the corresponding bucket but it is not easy, in general, to determine the next bucket that must be examined The dif culty arises because a good hash function assigns values randomly to buckets Thus, there is no simple notion of next bucket in sorted order The reason we cannot chain buckets together in sorted order on Ai is that each bucket is assigned many search-key values Since values are scattered randomly by the hash function, the values in the speci ed range are likely to be scattered across many or all of the buckets Therefore, we have to read all the buckets to nd the required search keys Usually the designer will choose ordered indexing unless it is known in advance that range queries will be infrequent, in which case hashing would be chosen Hash organizations are particularly useful for temporary les created during query processing, if lookups based on a key value are required, but no range queries will be performed

ciscoasa# show mac-address-table [logical_if_name | count | static]